Cisco 678 Subnet - Revision history

Envy at 20:50, 4 December 2017

2017-12-04T20:50:48Z

← Older revision		Revision as of 14:50, 4 December 2017
Line 1:		Line 1:
	{{~~Archive~~}}		{{Archived}}

	DSL Configuration for Cisco 678 in PPP (DMT), Multiple IP Addresses		DSL Configuration for Cisco 678 in PPP (DMT), Multiple IP Addresses

Envy at 20:50, 4 December 2017

2017-12-04T20:50:35Z

← Older revision		Revision as of 14:50, 4 December 2017
Line 1:		Line 1:
			{{Archive}}

	DSL Configuration for Cisco 678 in PPP (DMT), Multiple IP Addresses		DSL Configuration for Cisco 678 in PPP (DMT), Multiple IP Addresses

Jab at 21:42, 27 January 2014

2014-01-27T21:42:34Z

← Older revision		Revision as of 15:42, 27 January 2014
Line 78:		Line 78:
	#write		#write
	#reboot		#reboot
	[[Category:~~DSLTroubleshooting~~]]		[[Category:DSL Troubleshooting]]
	{{footer}}		{{footer}}

Jab at 21:42, 27 January 2014

2014-01-27T21:42:26Z

← Older revision		Revision as of 15:42, 27 January 2014
Line 78:		Line 78:
	#write		#write
	#reboot		#reboot
			[[Category:DSLTroubleshooting]]
	{{footer}}		{{footer}}

Mfrazier at 15:51, 21 May 2008

2008-05-21T15:51:27Z

← Older revision		Revision as of 09:51, 21 May 2008
Line 12:		Line 12:
	#At the [Password] prompt, hit the Enter key.		#At the [Password] prompt, hit the Enter key.
	#Type "enable" and hit the Enter key twice.		#Type "enable" and hit the Enter key twice.
	#~~Issue the following commands:~~		#show version
	~~<pre>~~show version~~</pre>~~

	*Note: The Cisco 678 requires v2.4.0 or higher for proper PPP operation. XMission		*Note: The Cisco 678 requires v2.4.0 or higher for proper PPP operation. XMission

Mfrazier at 15:50, 21 May 2008

2008-05-21T15:50:47Z

← Older revision		Revision as of 09:50, 21 May 2008
Line 10:		Line 10:


	1) At the [Password] prompt, hit the Enter key.		#At the [Password] prompt, hit the Enter key.
	2) Type "enable" and hit the Enter key twice.		#Type "enable" and hit the Enter key twice.
	Issue the following commands:		#Issue the following commands:
	3) show version		<pre>show version</pre>

	*Note: The Cisco 678 requires v2.4.0 or higher for proper PPP operation. XMission		*Note: The Cisco 678 requires v2.4.0 or higher for proper PPP operation. XMission
Line 21:		Line 21:
	are contained within the README file.		are contained within the README file.

	4) set nvram erase		#set nvram erase
	5) write		#write
	6) reboot		#reboot

	*Note: The 678 will reboot and bring you back to a "Password" prompt.		*Note: The 678 will reboot and bring you back to a "Password" prompt.

	7) Press Enter.		#Press Enter.
	8) Type "enable" and hit the Enter key twice.		#Type "enable" and hit the Enter key twice.
	~~Issue the following commands:~~		#Set interface wan0-0 disable
	~~9) set~~ interface wan0-0 disable

	*Note: Some versions require "set interface wan0-0 close".		*Note: Some versions require "set interface wan0-0 close".

	~~10)~~ set interface wan0-0 vpi 0		#set interface wan0-0 vpi 0
	~~11)~~ set interface wan0-0 vci 32		#set interface wan0-0 vci 32
	~~12)~~ set interface wan0-0 enable		#set interface wan0-0 enable

	*Note: Some versions require "set interface wan0-0 open".		*Note: Some versions require "set interface wan0-0 open".

	~~13)~~ set web disabled		#set web disabled
	~~14)~~ set web port 8081		#set web port 8081
	~~15)~~ write		#write
	~~16)~~ reboot		#reboot

	*Note: Again, the 678 will reboot and bring you back to a "Password" prompt.		*Note: Again, the 678 will reboot and bring you back to a "Password" prompt.

	~~17)~~ Press Enter.		#Press Enter.
	~~18)~~ Type "enable" and hit the Enter key twice.		#Type "enable" and hit the Enter key twice.
	~~Issue the following commands:~~		#set ppp wan0-0 ipcp 0.0.0.0
	~~19)~~ set ppp wan0-0 ipcp 0.0.0.0		#set ppp wan0-0 login acctname (where acctname is your XMission username)
	~~20)~~ set ppp wan0-0 login acctname (where acctname is your XMission username)		#set ppp wan0-0 password mypasswd (where mypasswd is your XMission login password)
	~~21)~~ set ppp wan0-0 password mypasswd (where mypasswd is your XMission login		#set ppp restart enabled
	password)		#set bridging rfc1483 off
	~~22)~~ set ppp restart enabled		#write
	~~23)~~ set bridging rfc1483 off		#reboot
	~~24)~~ write
	~~25)~~ reboot

	*Note: The 678 will, again, reboot.		*Note: The 678 will, again, reboot.

	~~26)~~ Press Enter.		#Press Enter.
	~~27)~~ Type "enable" and hit the Enter key twice.		#Type "enable" and hit the Enter key twice.
	~~Issue the following commands:~~		#set nat disabled
	~~28)~~ set nat disabled		#set interface eth0 address x.x.x.x (where x.x.x.x is the first usable IP in your subnet)
	~~29)~~ set interface eth0 address x.x.x.x (where x.x.x.x is the first usable IP in		#set interface eth0 netmask 255.255.255.x (where 255.255.255.x is your subnet mask)
	your subnet)
	~~30)~~ set interface eth0 netmask 255.255.255.x (where 255.255.255.x is your subnet
	mask)

	*Note: To calculate your subnet mask, subtract the number of IP addresses in your		*Note: To calculate your subnet mask, subtract the number of IP addresses in your
Line 75:		Line 69:
	255.255.255.248.		255.255.255.248.

	~~31)~~ set password exec myexecpw (where myexecpw is any password you choose)		#set password exec myexecpw (where myexecpw is any password you choose)
	~~32)~~ set password enable myenablepw (where myenablepw is any password you choose)		#set password enable myenablepw (where myenablepw is any password you choose)

	*Note: CBOS version v2.4.0 will not allow telnet from any source until passwords		*Note: CBOS version v2.4.0 will not allow telnet from any source until passwords
Line 83:		Line 77:
	In both circumstances, XMission recommends you set passwords for your router.		In both circumstances, XMission recommends you set passwords for your router.

	~~33)~~ write		#write
	~~34)~~ reboot		#reboot

			{{footer}}

Mfrazier: New page: DSL Configuration for Cisco 678 in PPP (DMT), Multiple IP Addresses Before you begin, you will need connect the management serial cable that came with your 678. It will need to be connect...

2008-05-21T15:46:44Z

New page: DSL Configuration for Cisco 678 in PPP (DMT), Multiple IP Addresses Before you begin, you will need connect the management serial cable that came with your 678. It will need to be connect...

New page

DSL Configuration for Cisco 678 in PPP (DMT), Multiple IP Addresses

Before you begin, you will need connect the management serial cable that came with
your 678. It will need to be connected to the "MGMT" port on the back of the 678
and a serial port on your computer. You will then need to connect to the 678 with
terminal software (e.g.: Hyperterminal, ZTerm, Minicomm, Telix). The speed the
terminal software will communicate with the 678 will be either 9600 or 38400, no
software or hardware handshaking.

1) At the [Password] prompt, hit the Enter key.
2) Type "enable" and hit the Enter key twice.
Issue the following commands:
3) show version

*Note: The Cisco 678 requires v2.4.0 or higher for proper PPP operation. XMission
recommends v2.4.3. This is available for customer FTP
by logging into "ftp.xmission.com" with customer's account and password
then changing to the "/archive/dsl" directory. Instructions for upgrading
are contained within the README file.

4) set nvram erase
5) write
6) reboot

*Note: The 678 will reboot and bring you back to a "Password" prompt.

7) Press Enter.
8) Type "enable" and hit the Enter key twice.
Issue the following commands:
9) set interface wan0-0 disable

*Note: Some versions require "set interface wan0-0 close".

10) set interface wan0-0 vpi 0
11) set interface wan0-0 vci 32
12) set interface wan0-0 enable

*Note: Some versions require "set interface wan0-0 open".

13) set web disabled
14) set web port 8081
15) write
16) reboot

*Note: Again, the 678 will reboot and bring you back to a "Password" prompt.

17) Press Enter.
18) Type "enable" and hit the Enter key twice.
Issue the following commands:
19) set ppp wan0-0 ipcp 0.0.0.0
20) set ppp wan0-0 login acctname (where acctname is your XMission username)
21) set ppp wan0-0 password mypasswd (where mypasswd is your XMission login
password)
22) set ppp restart enabled
23) set bridging rfc1483 off
24) write
25) reboot

*Note: The 678 will, again, reboot.

26) Press Enter.
27) Type "enable" and hit the Enter key twice.
Issue the following commands:
28) set nat disabled
29) set interface eth0 address x.x.x.x (where x.x.x.x is the first usable IP in
your subnet)
30) set interface eth0 netmask 255.255.255.x (where 255.255.255.x is your subnet
mask)

*Note: To calculate your subnet mask, subtract the number of IP addresses in your
subnet from 256. The result is the last number of your subnet mask. For example,
if you have 8 IP addresses, subtract 8 from 256. The resulting subnet mask is
255.255.255.248.

31) set password exec myexecpw (where myexecpw is any password you choose)
32) set password enable myenablepw (where myenablepw is any password you choose)

*Note: CBOS version v2.4.0 will not allow telnet from any source until passwords
have been set for both "exec" and "enable" modes. Earlier versions allow telnet,
and in fact will allow any access to its configuration unless password protected.
In both circumstances, XMission recommends you set passwords for your router.

33) write
34) reboot