Sonicwall Configuration for XMission Voice - Revision history

Danzmo: /* Create Address Group for Voice Services */

2022-08-17T15:36:58Z

Create Address Group for Voice Services

← Older revision		Revision as of 09:36, 17 August 2022
Line 67:		Line 67:
	# Click Firewall > Address Objects > Add		# Click Firewall > Address Objects > Add
	# Fill out the following:		# Fill out the following:
	:* Name: Name of the Assignment		#:* Name: Name of the Assignment
	:* Zone Assignment: WAN		#:* Zone Assignment: WAN
	:* Type: Host		#:* Type: Host
	:* IP Address:		#:* IP Address:
	::(SLC) SUMOFIBER colocation: 198.91.51.90		#::: (SLC) SUMOFIBER colocation: 198.91.51.90
	::(SLC) XMISSION colocation: 208.83.224.245		#::: (SLC) XMISSION colocation: 208.83.224.245
	::(LAS) SWITCH colocation: 162.252.224.11		#::: (LAS) SWITCH colocation: 162.252.224.11
	# Add each IP Address for Voice Services as an Address Object		# Add each IP Address for Voice Services as an Address Object
	:# [[File:Address_Group.png]]		#: [[File:Address_Group.png\|400px]]
	# Create an Address Group and add the address objects that were created		# Create an Address Group and add the address objects that were created
	:* Name: Voice Services		#:* Name: Voice Services


	== Excluding Voice Services IPs under Security Services (if applicable) ==		== Excluding Voice Services IPs under Security Services (if applicable) ==

Danzmo: /* Create LAN > WAN Rule for Services */

2022-08-17T15:36:09Z

Create LAN > WAN Rule for Services

← Older revision		Revision as of 09:36, 17 August 2022
Line 49:		Line 49:
	# Click on the arrow under LAN > WAN		# Click on the arrow under LAN > WAN
	# Click on Add...		# Click on Add...
	:* Source Port: Any		#:* Source Port: Any
	:* Service: VOIP Services		#:* Service: VOIP Services
	:* Source: Any		#:* Source: Any
	:* Destination: Any		#:* Destination: Any
	:* Users Included: All		#:* Users Included: All
	:* Users Excluded: None		#:* Users Excluded: None
	:* Schedule: Always On		#:* Schedule: Always On
	:* Comment: QoS for VoIP Phones		#:* Comment: QoS for VoIP Phones
	:* Enable Logging: True		#:* Enable Logging: True
	:* Allow Fragmented Packets: True		#:* Allow Fragmented Packets: True
	:# [[File:Lan_Wan_Rule.png]]		#: [[File:Lan_Wan_Rule.png\|600px]]
	# Click on the Advanced tab		# Click on the Advanced tab
	:* UDP Connection Inactivity Timeout (seconds): 90		#:* UDP Connection Inactivity Timeout (seconds): 90
	[[File:Lan_Wan_Rule(2).png]]		# [[File:Lan_Wan_Rule(2).png\|600px]]

	== Create Address Group for Voice Services ==		== Create Address Group for Voice Services ==

Danzmo: /* Create Custom VoIP Services */

2022-08-17T15:35:14Z

Create Custom VoIP Services

← Older revision		Revision as of 09:35, 17 August 2022
Line 30:		Line 30:
	# Under Network > Services click Add...		# Under Network > Services click Add...
	# Fill the popup as follows:		# Fill the popup as follows:
	:* Name: VoIP RTP		#:* Name: VoIP RTP
	:* Protocol: UDP		#:* Protocol: UDP
	:* Port Range: 3000 - 65000		#:* Port Range: 3000 - 65000
	:* Sub Type: None		#:* Sub Type: None
	# Click Add		# Click Add
	:# [[File:Custom_Voip.png]]		#: [[File:Custom_Voip.png\|400px]]
	# Click on Service Groups > Add Group...		# Click on Service Groups > Add Group...
	# Name: VOIP Services		# Name: VOIP Services
	# Add the following services to the right box		# Add the following services to the right box
	:* SIP		#:* SIP
	:* VoIP RTP		#:* VoIP RTP
	:* Click Add		#:* Click Add
	[[File:Custom_Voip(2).png]]		#: [[File:Custom_Voip(2).png\|400px]]


	== Create LAN > WAN Rule for Services ==		== Create LAN > WAN Rule for Services ==

Danzmo: /* Advanced Firewall Settings */

2022-08-17T15:34:29Z

Advanced Firewall Settings

← Older revision		Revision as of 09:34, 17 August 2022
Line 24:		Line 24:
	# Click on Advanced		# Click on Advanced
	# Select the check boxes for Enable Stealth Mode and Randomize IP ID		# Select the check boxes for Enable Stealth Mode and Randomize IP ID
	#: [[File:Advanced_Firewall.png~~\|600px~~]]		#: [[File:Advanced_Firewall.png]]
	# Click Accept		# Click Accept

Danzmo: /* Advanced Firewall Settings */

2022-08-17T15:34:16Z

Advanced Firewall Settings

← Older revision		Revision as of 09:34, 17 August 2022
Line 23:		Line 23:
	# Click on Firewall Settings		# Click on Firewall Settings
	# Click on Advanced		# Click on Advanced
	# Select the check boxes for Enable Stealth ~~Modeand~~ Randomize IP ID		# Select the check boxes for Enable Stealth Mode and Randomize IP ID
	:# [[File:Advanced_Firewall.png]]		#: [[File:Advanced_Firewall.png\|600px]]
	# Click Accept		# Click Accept

Danzmo: /* Consistent NAT */

2022-08-17T15:34:02Z

Consistent NAT

← Older revision		Revision as of 09:34, 17 August 2022
Line 16:		Line 16:
	# Select the checkbox for Enable consistent NAT		# Select the checkbox for Enable consistent NAT
	# Every other checkbox on this page should be unchecked		# Every other checkbox on this page should be unchecked
	:# [[File:Consistent_Nat.png]]		#: [[File:Consistent_Nat.png\|600px]]
	# Click Accept		# Click Accept

Danzmo: Created page with "If you have a Sonicwall and are using XMission Business or HostedPBX Voice Service you may come into issues such as: * Registration failure * Slow to dial out * Non-clear HD..."

2022-08-17T15:33:37Z

Created page with "If you have a Sonicwall and are using XMission Business or HostedPBX Voice Service you may come into issues such as: * Registration failure * Slow to dial out * Non-clear HD..."

New page

If you have a Sonicwall and are using XMission Business or HostedPBX Voice Service you may come into issues such as:

* Registration failure
* Slow to dial out
* Non-clear HD Voice quality
* and more.

We suggest that the following settings are set up in the Sonicwall Device.

''NOTE: depending on the model and firmware, the images may not match.''

== Consistent NAT ==

# Click on VoIP
# Click on Settings
# Select the checkbox for Enable consistent NAT
# Every other checkbox on this page should be unchecked
:# [[File:Consistent_Nat.png]]
# Click Accept

== Advanced Firewall Settings ==

# Click on Firewall Settings
# Click on Advanced
# Select the check boxes for Enable Stealth Modeand Randomize IP ID
:# [[File:Advanced_Firewall.png]]
# Click Accept

== Create Custom VoIP Services ==
# Under Network > Services click Add...
# Fill the popup as follows:
:* Name: VoIP RTP
:* Protocol: UDP
:* Port Range: 3000 - 65000
:* Sub Type: None
# Click Add
:# [[File:Custom_Voip.png]]
# Click on Service Groups > Add Group...
# Name: VOIP Services
# Add the following services to the right box
:* SIP
:* VoIP RTP
:* Click Add
[[File:Custom_Voip(2).png]]

== Create LAN > WAN Rule for Services ==
# Navigate to Firewall > Access Rules
# Click on Matrix
# Click on the arrow under LAN > WAN
# Click on Add...
:* Source Port: Any
:* Service: VOIP Services
:* Source: Any
:* Destination: Any
:* Users Included: All
:* Users Excluded: None
:* Schedule: Always On
:* Comment: QoS for VoIP Phones
:* Enable Logging: True
:* Allow Fragmented Packets: True
:# [[File:Lan_Wan_Rule.png]]
# Click on the Advanced tab
:* UDP Connection Inactivity Timeout (seconds): 90
[[File:Lan_Wan_Rule(2).png]]

== Create Address Group for Voice Services ==
# Click Firewall > Address Objects > Add
# Fill out the following:
:* Name: Name of the Assignment
:* Zone Assignment: WAN
:* Type: Host
:* IP Address:
::(SLC) SUMOFIBER colocation: 198.91.51.90
::(SLC) XMISSION colocation: 208.83.224.245
::(LAS) SWITCH colocation: 162.252.224.11
# Add each IP Address for Voice Services as an Address Object
:# [[File:Address_Group.png]]
# Create an Address Group and add the address objects that were created
:* Name: Voice Services

== Excluding Voice Services IPs under Security Services (if applicable) ==
# Click Security Services
# Check each Service and see if it is enabled
# If so, you need to enable the Exclusion List on each service and set it to Voice Services
# Example: Content Filter
:# [[File:Exclude_Services.png]]
# Once you exclude it, click Accept