Difference between revisions of "Cisco IOS"
(Created page with '===Cisco IOS PPPoE Proceedure=== '''The following should work for most Cisco IOS versions.''' On a Cisco device running IOS you will want to create a new PPPoE interface/dialer…') |
|||
| Line 4: | Line 4: | ||
On a Cisco device running IOS you will want to create a new PPPoE interface/dialer. The following should be what is needed: | On a Cisco device running IOS you will want to create a new PPPoE interface/dialer. The following should be what is needed: | ||
| + | |||
<pre> | <pre> | ||
| − | interface Dialer1 | + | '''interface Dialer1 |
ip address negotiated (you can also specify the ip with <xm ip address> <subnet mask>, but this is not recommended) | ip address negotiated (you can also specify the ip with <xm ip address> <subnet mask>, but this is not recommended) | ||
ip virtual-reassembly | ip virtual-reassembly | ||
| Line 12: | Line 13: | ||
dialer-group 1 | dialer-group 1 | ||
no cdp enable | no cdp enable | ||
| − | ppp pap sent-username <xmusername> password <xmpassword> | + | ppp pap sent-username <xmusername> password <xmpassword> ''' |
</pre> | </pre> | ||
Revision as of 16:27, 9 November 2012
Cisco IOS PPPoE Proceedure
The following should work for most Cisco IOS versions.
On a Cisco device running IOS you will want to create a new PPPoE interface/dialer. The following should be what is needed:
'''interface Dialer1 ip address negotiated (you can also specify the ip with <xm ip address> <subnet mask>, but this is not recommended) ip virtual-reassembly encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp pap sent-username <xmusername> password <xmpassword> '''
You will then want to configure the WAN port interface to use this dialer:
interface FastEthernet<whatever interface> no ip address no ip redirects no ip unreachables no ip proxy-arp ip tcp adjust-mss 1452 duplex auto speed auto pppoe enable pppoe-client dial-pool-number 1
Below is a walk through on what commands to enter:
After you telnet to the router and are at the CLI (command line interface) you will need to enter enable mode:
router>enable password: router#
You will then need to enter the configuration terminal to edit/add interfaces and commands:
router#config t Enter configuration commands, one per line. End with CNTL/Z. router(config)#
The next step is to configure the dialer/pppoe interface. We named this example Dialer1:
router(config)#interface Dialer1 router(config-if)#
Now all we need to do is add the options:
router(config-if)#ip address negotiated router(config-if)#ip virtual-reassembly router(config-if)#encapsulation ppp router(config-if)#dialer pool 1 router(config-if)#dialer-group 1 router(config-if)#no cdp enable router(config-if)#ppp pap sent-username <xmusername> password <xmpassword> router(config-if)#exit
Last we need to configure the physical interface on the WAN port:
router(config)#interface FastEthernet<whatever interface> router(config-if)#no ip address router(config-if)#no ip redirects router(config-if)#no ip unreachables router(config-if)#no ip proxy-arp router(config-if)#ip tcp adjust-mss 1452 router(config-if)#duplex auto router(config-if)#speed auto router(config-if)#pppoe enable router(config-if)#pppoe-client dial-pool-number 1 router(config-if)#exit
Now we just need to exit and write the changes:
router(config)#exit router#write
