Difference between revisions of "Juniper"
(Created page with '===Juniper PPPoE Proceedure=== Juniper users a hierarchical configuration and the PPPoE settings fall under the interfaces section. In this example we will be using the fast eth…') |
(→Juniper PPPoE Proceedure) |
||
| Line 2: | Line 2: | ||
Juniper users a hierarchical configuration and the PPPoE settings fall under the interfaces section. In this example we will be using the fast ethernet port 0/0/1 for the WAN interface and the final configuration will look like: | Juniper users a hierarchical configuration and the PPPoE settings fall under the interfaces section. In this example we will be using the fast ethernet port 0/0/1 for the WAN interface and the final configuration will look like: | ||
| − | < | + | <poem> |
interfaces { | interfaces { | ||
fe-0/0/1 { | fe-0/0/1 { | ||
| Line 32: | Line 32: | ||
} | } | ||
} | } | ||
| − | </ | + | </poem> |
'''Below is a walk through on what commands to enter:''' | '''Below is a walk through on what commands to enter:''' | ||
You will want to ssh / telnet to the router and be at the CLI (command line interface): | You will want to ssh / telnet to the router and be at the CLI (command line interface): | ||
| − | < | + | <poem> |
--- JUNOS 11.4xxxx built 2011-05-15 22:21:00 UTC | --- JUNOS 11.4xxxx built 2011-05-15 22:21:00 UTC | ||
{master} | {master} | ||
user@router> | user@router> | ||
| − | </ | + | </poem> |
We will need to be in the edit mode at this point: | We will need to be in the edit mode at this point: | ||
| − | < | + | <poem> |
user@router>edit | user@router>edit | ||
| Line 51: | Line 51: | ||
{master}[edit] | {master}[edit] | ||
user@router# | user@router# | ||
| − | </ | + | </poem> |
Now we will want to set the interface FastEthernet 0/0/1 to use PPPoE encapsulation: | Now we will want to set the interface FastEthernet 0/0/1 to use PPPoE encapsulation: | ||
| − | < | + | <poem> |
user@router#edit interfaces fe-0/0/1 unit 0 | user@router#edit interfaces fe-0/0/1 unit 0 | ||
| Line 63: | Line 63: | ||
{master}[edit] | {master}[edit] | ||
user@router# | user@router# | ||
| − | </ | + | </poem> |
Next we will want to edit the ppp pap options pp0 interface: | Next we will want to edit the ppp pap options pp0 interface: | ||
| − | < | + | <poem> |
user@router#edit interfaces pp0 unit 0 ppp-options pap | user@router#edit interfaces pp0 unit 0 ppp-options pap | ||
| Line 78: | Line 78: | ||
{master} | {master} | ||
user@router# | user@router# | ||
| − | </ | + | </poem> |
Now we will want to configure the pppoe options: | Now we will want to configure the pppoe options: | ||
| − | < | + | <poem> |
user@router#edit interfaces pp0 unit 0 pppoe-options | user@router#edit interfaces pp0 unit 0 pppoe-options | ||
| Line 93: | Line 93: | ||
{master} | {master} | ||
user@router# | user@router# | ||
| − | </ | + | </poem> |
Last we will want to set the ip address, in this example we will use auto negotiate: | Last we will want to set the ip address, in this example we will use auto negotiate: | ||
| − | < | + | <poem> |
user@router#edit interfaces pp0 unit 0 family-inet | user@router#edit interfaces pp0 unit 0 family-inet | ||
| Line 106: | Line 106: | ||
{master} | {master} | ||
user@router# | user@router# | ||
| − | </ | + | </poem> |
Then just commit these changes and exit edit mode | Then just commit these changes and exit edit mode | ||
Revision as of 10:33, 10 November 2012
Juniper PPPoE Proceedure
Juniper users a hierarchical configuration and the PPPoE settings fall under the interfaces section. In this example we will be using the fast ethernet port 0/0/1 for the WAN interface and the final configuration will look like: <poem> interfaces {
fe-0/0/1 {
unit 0 {
encapsulation ppp-over-ether;
}
}
pp0 {
unit 0 {
ppp-options {
pap {
access-profile ppp-profile;
local-password "dkwoxslxqpz";##SECRET-DATA
local-name "username";
passive;
}
}
pppoe-options {
underlying-interface fe-0/0/1.0;
auto-reconnect 10;
client;
idle-timeout 0;
}
family inet {
negotiate-address;
mtu 1492;
}
}
}
} </poem>
Below is a walk through on what commands to enter:
You will want to ssh / telnet to the router and be at the CLI (command line interface): <poem> --- JUNOS 11.4xxxx built 2011-05-15 22:21:00 UTC {master} user@router> </poem>
We will need to be in the edit mode at this point: <poem> user@router>edit
Entering configuration mode Users currently editing the configuration: {master}[edit] user@router# </poem>
Now we will want to set the interface FastEthernet 0/0/1 to use PPPoE encapsulation: <poem> user@router#edit interfaces fe-0/0/1 unit 0
{master}[edit interfaces fe-0/0/1 unit 0] user@router#set encapsulation ppp-over-ether; user@router#exit
{master}[edit] user@router# </poem>
Next we will want to edit the ppp pap options pp0 interface: <poem> user@router#edit interfaces pp0 unit 0 ppp-options pap
{master}[edit interfaces pp0 unit 0 ppp-options pap] user@router#set access-profile ppp-profile user@router#set local-password "xmission password" user@router#set local-name "xmission username" user@router#set passive user@router#exit
{master} user@router# </poem>
Now we will want to configure the pppoe options: <poem> user@router#edit interfaces pp0 unit 0 pppoe-options
{master}[edit interfaces pp0 unit 0 pppoe-options] user@router#set underlying-interface fe-0/0/1.0 user@router#set auto-reconnect 10 user@router#set client user@router#set idle-timeout 0 user@router#exit
{master} user@router# </poem>
Last we will want to set the ip address, in this example we will use auto negotiate: <poem> user@router#edit interfaces pp0 unit 0 family-inet
{master}[edit interfaces pp0 unit 0 family-inet] user@router#set negotiate-address user@router#set mtu 1492 user@router#exit
{master} user@router# </poem>
Then just commit these changes and exit edit mode
