Latest revision as of 10:50, 15 March 2024

SPF and DKIM are two important security methods domain owners have of "authorizing" specific email servers to send mail on their behalf. Besides providing greater deliverability of your messages, these mechanisms prevent fraudsters from sending spoofing emails as your domain.

These TXT records are entered by the domain owner wherever the domain's DNS record is managed, which may be with the registrar or hosting provider. DKIM (Domain Key Identified Mail) also adds public key cryptography for deeper validation.

XMission advises all Zimbra clients to configure SPF & DKIM. It may sound a bit daunting but is really not very complicated. This document will walk you through it.

IMPORTANT NOTE ABOUT TXT RECORD ENTRY: Depending on the syntax requirements of your DNS system you may have to include or omit the quotation marks for the record to be properly enabled. Other DNS entries on your domain should provide quick visual guidance on protocol. XMission DNS systems do not use quotation marks.

SPF

The following is the most commonly applied SPF (Sender Policy Framework) record for XMission email customers but it is imperative you understand how and why this is applied. IMPORTANT: It is critical that you read and understand all SPF information below before applying the record to your domain as you could break email delivery.

How It Works

Any SPF record is a string of one more more potential mail sources, prefixed by a character indicating the policy for mail source. An example of a common SPF record:

In this case, it says that the A and MX records for the domain are allowed to send, and all other mail fails (but with a "softfail", so that mail isn't actually rejected). "a", "mx" and "all", are all individual mail sources. The "~" prefixed to the "all" source is a policy denoting that mail from the source should be considered a "SoftFail".

XMission Shared Hosting clients can learn to manage DNS records here.

Valid SPF for XMission

Any SPF record for a domain sending through XMission should contain "include:_spf.xmission.com".

If you prefer a less identifiable entry then a minimum inclusion would have the following four sources:

• ip4:166.70.11.0/24
• ip4:166.70.13.0/24
• ip4:166.70.198.0/24
• ip4:198.60.22.0/24

Note that the SPF record policy is a decision of the domain owner's. If they want to Fail or SoftFail on all, add other sources, etc., is up to them. We don't have a singular recommendation or requirement for SPF. If the customer only sends via XMission, the following SPF record is relatively safe:

Valid SPF for XMission with additional sending services

Sometimes it is necessary to have mailing list or other services that need to send emails so having multiple SPF records be strung together becomes necessary. Fortunately the fairly lenient syntax of SPF records makes this easy to do, here is our default record compared to some merged records:

Forwarding

Important note about forwarding (ie automatically redirecting mail from one email address to another, not hitting the forward button):

Forwarding (under most circumstances) BREAKS SPF. If a domain has a "-all" ("reject all other mail" aka "Fail") policy in their SPF record, mail will be rejected by any servers respecting SPF after the server performing the forward. Users should keep this in mind when choosing a policy. This is why we suggest "~all" ("SoftFail") when you initially configure SPF.

Alias Domains

Domain aliases that are used for sending email with "From:" addresses will need SPF & DKIM records configured.

All customers are strongly encouraged to configure SPF & DKIM records for all alias domains and parked domains to prevent possible abuse.

DKIM

DomainKeys Identified Mail (DKIM) is similar to SPF in that it uses a TXT record on the domain to define a sending policy for that domain. Where it differs is that it uses public key cryptography with this sending policy. A public key is added to that TXT record and any message that is signed with the private key (and thus validates with the public key) is then considered valid.

DKIM will break automatic responders, like Out of Office or Vacation replies. This is due to how DKIM verifies the sender, and how automated replies are generated and sent. This is intentional, and is a consideration that needs to be made when limiting sending from your domain via DKIM.

Adding DKIM to an XMission Domain

We have a single private key for XMission DKIM signing. We can sign DKIM with this key on any domain sending out through XMission. It works for Zimbra domains, virtmail, and SMTP relay. To enable this feature for a domain, two things need to happen:

• The domain needs proper DNS for our domainkey key (see below)
• The domain needs to be added to XMission routing config as one with DKIM signing.

DKIM DNS

Add the following two TXT records to the domain.

Note: Once added you must contact support@xmission.com to add your domain to XMission's DKIM routing file and complete the process:

Reminder: XMission DNS systems do not require entry of the quotation marks on the records above. External DNS system may require quotation marks.

• _domainkey "t=y; o=~;" - is considered the DomainKeys Policy Record
  • o — Outbound Signing policy ('-' means that this domain signs all email, '~' is the default and means that this domain may sign some email with DomainKeys).
  • t — testing mode ('y' means that this domain is testing DomainKeys so unsigned and unverifiable email should not be treated differently from verified email. Recipient systems may wish to track testing mode results to assist the sender.)

Multiple Email Hosts with DKIM

It is possible to use more than one host with DKIM, though this is only possible if the DNS records used to announce the public key for the security handshake don't share subdomains with each other.